Information about Single Lens Reflex Camera

The single-lens reflex (SLR) camera is a photographic imaging instrument that currently uses an automatic moving mirror system and viewing pentaprism, which is situated between the lens and the film plane to direct the light reflected from the subject's image, then passing through the attached lens, with the light being reflected by the 45 degree angle mirror to the optical pentaprism, where the light is again reflected two more times until it passes through the viewfinder lens. The image can then be composed by the photographer; the focus can be adjusted manually (or automatically) by either the photographer (or the autofocus system if the camera is thus equipped); and then the photographer can release the shutter, thereby exposing the film (or, in the case of a DSLR, the CCD or CMOS imaging sensor). The viewfinder includes a matte focusing screen located just above the mirror system to diffuse the light, then to allow the light into the pentaprism, where it is reflected and then through the viewfinder lens to the photographer's eye. This system permits accurate viewing, composing and focusing, especially useful with interchangeable lenses.

Optical components of an SLR camera

A cross-section (or 'side-view') of the optical components of a typical SLR camera shows how the light passes through the lens assembly (1), is reflected by the mirror (2) and is projected on the matte focusing screen (5). Via a condensing lens (6) and internal reflections in the roof pentaprism (7) the image appears in the eyepiece (8). When an image is taken, the mirror moves upwards from its critical 45 degree angle in the direction of the arrow, the focal plane shutter (3) opens, and the image is projected onto the film or sensor (4) in exactly the same manner as on the focusing screen.

This feature distinguishes SLRs from other cameras as, the photographer sees the image composed exactly as it will be captured on the film or sensor (see Advantages below).

Pentaprisms and penta-mirrors

Most SLRs use a roof pentaprism or penta-mirror to direct the light to the eyepiece, but there are other finder viewing capabilities, such as the waist-level finder, the interchangeable sports finders used on the Canon F1, F1n and new F1; the Nikon F, F2, F3, F4 and F5; and the Pentax LX

Another prism design was the porro prism system used in the Olympus Pen F, the Pen FT, the Pen FV half-frame 35mm SLR cameras. This was later utilized on the digital Olympus EVOLT E-300 and E-330 DSLR cameras.

Lastly, a photographer can also purchase a right-angle finder which slips onto the eyepiece of most SLR's and D-SLR's and allows viewing sans a waist-level finder. There is also a finder which provides EVF remote capability.

Shutter mechanisms

Focal plane shutters

Almost all contemporary SLRs use a focal plane shutter located in front of the film plane, which prevents the light from reaching the film even if the lens is removed, except when the shutter is actually released during the exposure. There are various designs for focal plane shutters. Typical focal plane shutters designed in the fifties and continuing through part of the 1990's consisted of cloth material with two curtains: an opening shutter curtain followed by a closing shutter curtain. During fast shutter speeds, the focal plane shutter would form a 'slit' whereby the second shutter curtain was closely following the first opening shutter curtain to produce a narrow, vertical opening, with the shutter slit moving horizontally. The slit would get narrower as shutter speeds were increased.

Other focal plane shutter designs such as the Copal, travelled vertically. These were constructed of titanium foil and were metal-bladed (resembling something like a 'venetian blind'), and resulted in faster flash synchronization. Certain horizontally travelling focal plane shutters were also constructed of titanium foil as is the case with the Nikon F, F2, F3, F4, F5 and F6 35mm SLR cameras, and the Canon F-1 camera series. A unique focal plane shutter design was the rotary shutter used in the Olympus Pen half-frame 35mm SLR camera system. This shutter system was also titanium foil but consisted of one piece of metal with a fixed opening, and this shutter system allowed electronic flash (EF) synchronization up to and including its top shutter speed of 1/500 of a second, thereby rivaling leaf-shutter EF capabilities.

Leaf shutters - Two Types

Another shutter system is the leaf shutter, whereby the shutter is constructed of diaphragm-like blades and can be situated either between the lens or behind the lens. If the shutter is part of a lens assembly some other mechanism is required to ensure that no light reaches the film between exposures. The leaf shutter can either be situated between the lens or behind the lens assembly.

An example of a behind-the-lens leaf shutter is found in the 35mm SLR's produced by Kodak, with their Retina Reflex camera line; Topcon, with their Auto 100; and Kowa with their SE-R and SET-R reflexes.

An primary example of a medium-format SLR's with a between-the-lens leaf shutter system would be Hasselblad, with their 500C, 500CM, 500 EL-M (a motorized Hasselblad) and other models (producing a 2 1/4" square negative {or 6cm x 6cm metric}). Hasselblads use an auxiliary shutter blind situated behind the lens mount and the mirror system to prevent the fogging of film.

Other medium-format SLRs also using leaf shutters include the now discontinued Zenza-Bronica camera system lines such as the Bronica ETRs, the ETRs'i (both producing a 6 cm. x 4.5 cm. image), the SQ and the SQ-AI (producing a 2 1/4" or 6 x 6 cm. image like the Hasselblad), and the Zenza-Bronica G system (2 1/4" x 2 3/4" inch or 6 cm. x 7 cm.). Certain Mamiya medium-format SLRs, discontinued camera systems such as the Kowa 6 and a few other camera models also used between-the-lens leaf shutters in their lens systems.

Thus, anytime a photographer purchased a lens for the Hasselblad, with the exception of the older Hasselblad 1000f and other focal-plane shutter Hasselblads; or the Zenza-Bronica ETR, ETR-S, ETR-Si, the SQ, the SQ-Ai, the SQ-B, and the G series (with the exception of older Bronica cameras such as the Bronica Deluxe, the Bronica S, the Bronica S2), or the bigger system Mamiya RB-67, RB-67 Pro, RB-67 Pro S (mechanical) and RZ (electronically controlled shutter) cameras, that lens included a leaf shutter in its lens mount.

Because leaf shutters synchronized electronic flash at all shutter speeds especially at fast shutter speeds of 1/500 of a second or faster, cameras utilizing leaf shutters were more desired by studio photographers who used sophisticated studio electronic flash systems.

Some manufacturers of medium-format 2 1/4" SLR cameras also made leaf-shutter lenses for their focal plane shutter models. Rollei made at least two such lenses for their Rolleiflex SL-66 medium format, 2 1/4" camera, which was a focal-plane shutter SLR. Rollei later switched to a camera system of leaf-shutter design, (i.e., the 6006 and 6008 reflexes to name a few) and their current medium-format SLR's are now all of the between-the-lens shutter design.

Rotary shutter

One unusual design, the Olympus Pen half-frame 35mm SLR system, manufactured by Olympus in Japan, used a rotary focal plane shutter mechanism which was extremely simple and elegant in design, and enabled the photographer to synchronize electronic flash at all shutter speeds, including the shutter's limit to 1/500 of a second. The camera started out meterless with the introduction of the Olympus Pen F; this camera required a two-stroke advance of the advance lever. The later models, the Olympus Pen FT and the Olympus Pen FV only required a single stroke of the film advance lever to position the film to the next frame. The Olympus Pen FT has a behind-the-lens metering system and was composed of a number of impressive optics from a 20mm lens up to an 800mm catadioptric (mirror) telephoto lens. The system included 'fast' lenses such as the 38mm f/1.8 Zuiko, the 40mm f/1.4 Zuiko and the 42mm f/1.2 Zuiko, all considered 'normal' lenses for this format. Olympus also made a 38mm f/3.5 macro lens, and a bellows extension attachment. There were also various lens adapters and other accessories for this camera.

As a further, minor note on rotary shutters, only one other 35mm camera system used a rotary shutter, and this camera system was the Robot Royal cameras, most of which were rangefinder 35mm cameras. Some of these cameras were full-frame; some were half-frame, and at least one Robot camera produced an unusual square-sized image on the 35mm frame.

Further developments

Since the technology became widespread in the 1970s, SLRs have become the main photographic instrument used by dedicated amateur photographers and professionals. Some photographers of static subjects (i.e., architecture, landscape, and some commercial subjects), however, prefer view cameras [1] because of the capability to control perspective. With a triple-extension bellows 4" x 5" camera such as the Linhof SuperTechnika V, the photographer can correct certain distortions such as 'keystoning', where the image 'lines' converge (i.e., photographing a building by pointing a typical camera upward to include the top of the building). Perspective correction lenses are available in the 35mm and medium formats to correct this distortion with film cameras, and it can also be corrected after the fact with photo software when using digital cameras. The photographer can also extend the bellows to its full length, tilt the front standard and perform photomacrography (commonly known as 'macro photography'), producing a sharp image with depth-of-field without stopping down the lens diaphgram.

History

Main article: History of the single-lens reflex camera

The (Pentax) Asahiflex	The 35mm film-based Nikon F	Olympus The 35mm film-based Olympus OM-2, which was the first SLR to measure light for electronic flash off of the shutter curtain.	Two Classic 35mm SLR film cameras: the Canon AE-1 and the Minolta X-700
Nikon F5 professional SLR

Large format SLR cameras were probably first sold in 1884.^[1] The Ihagee Kine-Exakta was the first 35 mm SLR and it was truly influential. Further Exakta models, all with waist-level finders, were produced up to and during World War II. Another ancestor of the modern SLR camera was the Swiss-made Alpa, which was innovative, and influenced the later Japanese cameras. The first eye-level LSR viewfinder was patented in Hungary on August 23, 1943 by Jenő Dulovits, who then designed the first 35mm camera with one, the Duflex, which used a system of mirrors to provide a laterally correct, upright image in the eye-level viewfinder. The Duflex, which went into serial production in 1948, was also the world's first SLR with an instant-return (a.k.a. autoreturn) mirror.

The first commercially produced SLR that employed a roof pentaprism was the East German Contax S, announced on May 20, 1949.

The Japanese adopted and further developed the SLR. In 1952, Asahi developed the Asahiflex and in 1954, the Asahiflex IIB. In 1957, the Asahi Pentax combined the fixed pentaprism and the right-hand thumb wind lever. Nikon, Canon and Yashica introduced their first SLRs in 1959 (the F, Canonflex, and Pentamatic, respectively).

Through-the-lens light metering (also known as "behind-the-lens metering")

As a small matter of history, the first 35mm camera (non-SLR) to feature through the lens light metering may have been Nikon, with a prototype rangefinder camera, the SPX. According to the below website, the camera used Nikon 'S' type rangefinder lenses (See website: [2]

In the SLR design scheme, there were various placements made for the metering cells, all of which utilized CdS (Cadmium sulfide) photocells. The cells were either located in the pentaprism housing, where they metered light transmitted through the focusing screen; underneath the reflex mirror glass itself, which was Topcon's design; or in front of the shutter mechanism, which was the design used by Canon with their Canon Pellix.

Pentax was the first manufacturer to produce and show the first working prototype 35mm behind-the-lens metering SLR camera, which they named the Pentax Spotmatic. The camera was first shown at a Photokina show circa 1960-1961. Later, Through-the-lens (TTL) light metering SLRs were introduced to the photographic market in the early 1960s, starting with the 1963 production model Topcon RE Super which metered the light directly from a CdS metering system etched under the mirror/glass assembly. This system metered the light using an average metering system. Approximately one year later, in 1964, a production model of the Pentax Spotmatic was shown whose CdS light meter cells were housed in the pentaprism housing, reading the light coming upwards through the focusing screen. Pentax had reverted their original spot-metering design to an average metering scheme.

Mamiya Sekor came out with cameras such as the Mamiya Sekor TL and various other versions. Yashica introduced the TL Super. Both of these cameras used M42 screw thread lenses as did the Pentax Spotmatic. Later on Fujica introduced their ST-701, then ST-801 and ST-901 cameras. The ST-701 was the first SLR to use a silicon cell photodiode, which was more sensitive than CdS and was immune to the memory effect that the CdS cell suffered from in bright sunlight. Gradually, other 35mm SLR camera manufacturers changed their behind-the-lens meters from CdS cells to Silicon Diode photocells.

Other manufacturers responded and introduced their own behind-the-lens metering cameras. Nikon and Miranda, at first, simply upgraded their interchangeable pentaprisms to include behind-the-lens metering (for Nikon F, and Miranda D, F, Fv and G models) and these manufacturers also bought out other camera models with built-in behind-the-lens metering capability, such as the Nikkormat FT and the Miranda Sensorex (which used an external coupling diaphragm). Minolta introduced the SRT-101, which used Minolta's proprietary system which they referred to as "CLC", which was an acronym for "contrast light compensation", which metered differently from an average metering behind-the-lens camera.

Some german manufacturers also introduced cameras such as the Zeiss Ikon Contarex SE, which was the only 35mm SLR to use interchangeable film backs.

Inexpensive leaf-shutter cameras also benefited from behind-the-lens metering as, Topcon introduced the Auto 100 with front-mount interchangeable lenses designed only for that camera, and one of the Zeiss Ikon Contaflex leaf shutter cameras. Kowa manufactured their SET-R which had similar specifications.

Within months, manufacturers decided to bring out models that provided limited area metering, such as Nikon's Photomic Tn finder, which concentrated 60% of the CdS cells sensitivity on the inner circle of the focusing screen and 30% on the surrounding area. Canon used spot metering in the unusual Canon Pellix camera, which also had a stationary mirror system that allowed approximately 70% of the light to travel to the film plane and 30% to the photographer's eye. This system, unfortunately, degraded the native resolution of the attached lens and provided less illumination to the eyepiece. It did have the advantage of having less vibration than other SLR cameras but not sufficient enough to attract enough professionals to the camera.

Semi-automatic exposure capabilities

While auto-exposure was commonly used in the early 1960's with various 35mm fixed lens rangefinder cameras such as the Konica Auto 'S', and other cameras such as the Polaroid Land cameras whose early models used selenium cell meters, auto-exposure for interchangeable lens SLR's was a feature that was largely absent, except for a few early leaf-shutter SLR's such as the Kowa SE-R and Topcon Auto 100.

The types of automation found in some of these cameras consisted of the simple programmed shutter, whereby the camera's metering system would select a mechanically-set series of apertures with shutter speeds, one setting of which would be sufficient for the correct exposure. In the case of the above-mentioned Kowa and Topcon, automation was semi-automatic, where the camera's CDs meter would select the correct aperture only.

Autoexposure, technically known as semi-automatic exposure, where the camera's metering system chooses either the shutter speed or the aperture, was finally introduced by the Savoyflex and popularized by Konishiroku in the 1965 Konica Auto-Reflex. This camera was of the 'shutter-priority' type automation, which meant that the camera selected the correct aperture automatically. This model also had the interesting ability to photograph in 35mm full-frames or half-frames, all selected by a lever.

Other SLR's soon followed, but because of limitations with their lens mounts, the manufacturers of these cameras had to choose 'aperture-priority' automation, where the camera's metering system selects the correct shutter speed. As one example, Pentax introduced the Electro Spotmatic, which was able to use the then considerable bulk of 42mm screw-mount lenses produced by various manufacturers. Yashica, another screw-mount camera manufacturer, soon followed.

Canon, which produced the FD lens mount (known as the breech-mount; a unique lens mounting system that combines the advantages of screw-mount and bayonet-mount) introduced their shutter priority 35mm SLR, the Canon EF in 1976 or so. This camera's build quality was almost the equal of their flagship camera, the Canon F1, and featured a copal-square vertically-travelling focal plane shutter which could synchronize electronic flash at shutter speeds up to and including 1/125 of a second, thus making this a good second-body camera for the professional photographer.

Nikon at first, produced an aperture-priority camera, but later made subtle changes on the inside of their bayonet mount and soon, shutter-priority automation was achieved.

Full Program Auto-Exposure

Minolta XD-11 (also XD-7 and XD)
Type	35 mm SLR
Lens mount	Minolta MD mount
Focus	Manual focus SLR
Exposure	Shutter and Aperture priority autoexposure
Flash	Hot shoe only; no PC connector
Dimensions	51 x 86 x 136 mm, 560 g

Full-program auto-exposure soon followed with the advent of the Minolta XD-11.^[2] This SLR had a 'P' mode on the shutter speed dial, and a lock on the aperture ring to allow the lens to be put on 'Auto' mode. Other manufacturers soon followed with Nikon introducing the FA, Canon introducing the A1, and Pentax introducing the Super Program. Olympus, however, continued with 'aperture-priority' automation in their OM system line.

The 1970s and 1980s saw steadily increasing use of electronics, automation, and miniaturization, including integrated motor driven film advance with the Konica FS-1 in 1979, and motor rewind functions.

Autofocus

The first phase detection SLR TTL autofocus 35mm SLR was 1981's Pentax ME-F.^[3] The Minolta Maxxum 7000, released in 1985, was the first 35mm SLR with integrated motorized autofocus and film-advance winder, which became the standard configuration for SLR cameras from then on. This development had significant impact on the photographic industry.

Some manufacturers discarded their existing lens systems to compete with other manufacturer's autofocus capability in their new cameras. This was the case for Canon, with its new EOS lens line. Other manufacturers chose to adapt their existing lens systems for autofocus capability, as was the case with Nikon and Pentax. Still some manufacturers, notably Leica with its R-system lenses, and Contax with its Zeiss lenses, decided to keep their lens mounts non-autofocus. Before the Contax camera and lens line was totally discontinued, Contax did come out with autofocus and digital camera capability, evidenced in the Contax N-Digital. Unfortunately this model was too late and too expensive for competition with other camera manufacturers. The Contax N-digital was the last Contax to use that maker's lens system, and the camera, while having impressive features such as a full-frame sensor, lacked sufficient write-speed to the memory card for it to be seriously considered by some professional photographers.

From the late 1980s competition and technical innovations made 35mm camera systems more versatile and sophisticated by adding more advanced light metering capabilities such as spot-metering; limited area metering such as used by Canon with the F1 series; matrix metering as used by Nikon, exposure communication with dedicated electronic flash units. The user interface also changed on many cameras, replacing meter needle displays which were galvanometer-based and thereby fragile, with light-emitting diodes (LEDs) and then with more comprehensive liquid crystal displays (LCDs) both in the SLR viewfinder and externally on the cameras' top plate using an LCD screen. Wheels and buttons replaced the shutter dial on the camera and the aperture ring on the lens on many models, although some photographers still prefer shutter dials and aperture rings. Some manufacturers introduced image stabilization on certain lenses to combat camera shake and to allow longer hand-held exposures without using a tripod. This feature is especially useful with long telephoto lenses.

Digital SLRs (DSLRs)

Main article: Digital single-lens reflex camera

Canon, Nikon and Pentax have all developed digital SLR cameras using the same lens mounts as on their respective film SLR cameras. Konica Minolta did the same, but in 2006 sold their camera technology to Sony, who now build DSLRs based on the Minolta lens mount. Samsung builds DSLRs based on the Pentax lens mount. Olympus, on the other hand, chose to create a new digital-only Four Thirds System SLR standard, adopted later by Panasonic and Leica.

Film formats

Early SLRs were built for large format photography, but this film format has largely lost favor among professional photographers. SLR film-based cameras have been produced for most film formats as well as for digital formats. These film-based SLRs use the 35 mm format as, this film format offers a variety of emulsions and film sensitivity speeds, usable image quality and a good market cost. 35mm film comes in a variety of exposure lengths: 20 exposure, 24 exposure and 36 exposure rolls. Medium format SLRs provide a higher-quality image with a negative that can be retouched, unlike the 35mm negative, when this capability is required.

A small number of SLRs were built for APS such as the Canon IXUS and the Nikon Pronea cameras. SLRs were also introduced for film formats as small as Kodak's 110, such as the Pentax Auto 110 which had interchangeable lenses.

The advent of digital photography in the late 1990s and the increasing popularity and dominance of digital photography makes it very unlikely that there will ever be any new film formats.

Common features

Other features found on many SLR cameras include through-the-lens (TTL) metering and sophisticated flash control referred to as 'dedicated electronic flash'. In a dedicated system, once the dedicated electronic flash is inserted into the camera's hot shoe and turned on, there is then communication between camera and flash. The camera's synchronization speed is set, along with the aperture. Many camera models on the market today actually measure the light that reflects off of the film plane, controls the flash duration of the electronic flash (some flash units have a flash duration range of 1/1000 of a second to 1/50,000 of a second), and then terminate exposure when the camera has received enough light for the exposure.

Some electronic flash units can send out several short bursts of flash to measure the distance, use the camera's inboard sensor(s) to determine the amount of light that is reflected from the subject, then send out a main pulse of light of just the right amount of light energy for a perfectly exposed photograph. Sophisticated cameras can even make it easy for the photographer to balance electronic flash and available light for an evenly balanced scene. While these capabilities are hardly unique to the SLR, manufacturers included them early on in the top models, whereas the best rangefinder cameras adopted such features later.

Cut-away of a Minolta XG7 film-based SLR

Advantages

Many of the advantages of SLR cameras derive from viewing and focusing the image through the attached lens. Most other types of cameras do not have this function; subjects are seen through a viewfinder that is near the lens, making the photographer's view different from that of the lens. SLR cameras provide photographers with precision and confidence; they provide a viewing image that will be exposed onto the negative exactly as it is seen through the lens. There is no parallax error, and exact focus can be confirmed by eye — especially in macro photography and when photographing using long telephoto lenses. The depth of field may be seen by stopping down to the attached lens aperture, which is only possible on most SLR cameras except for the least expensive models. Because of the SLR's versatility, most manufacturers have a vast range of lenses and accessories available for them.

Compared to most fixed-lens compact cameras, the most commonly used and inexpensive SLR lenses offer a wider aperture range and larger maximum aperture (typically f/1.4 to f/1.8 for a 50 mm lens). This allows photographs to be taken in lower light conditions without flash, and allows a narrower depth of field, which is useful for blurring the background behind the subject, making the subject more prominent. 'Fast' lenses are commonly used in theater photography, portrait photography, surveillance photography, and all other photography requiring a large maximum aperture.

The variety of lenses also allows for the camera to be used and adapted in many different situations. This provides the photographer with considerably more control (i.e., how the image is viewed and framed) than would be the case with a view camera. In addition, some SLR lenses are manufactured with extremely long focal lengths, allowing a photographer to be a considerable distance away from the subject and yet still expose a sharp, focused image. This is particularly useful if the subject includes dangerous animals (e.g., wildlife); the subject prefers anonymity to being photographed; or else, the photographer's presence is unwanted (e.g., celebrity photography or surveillance photography). Practically all SLR and DSLR camera bodies can also be attached to telescopes and microscopes via an adapter tube to further enhance their imaging capabilities.

Disadvantages

In most cases, single-lens reflex cameras cannot be made as small or as light as other camera designs — such as rangefinder cameras, autofocus compact cameras and digital cameras with electronic viewfinders (EVF) — owing to the mirror box and pentaprism/pentamirror. The mirror box also prevents lenses from having rear elements closer to the film or sensor to be mounted unless the camera has a mirror lockup feature; this means that simple designs for wide angle lenses cannot be used. Instead, larger and more complex retrofocus designs are required.

The SLR mirror 'blacks-out' the viewfinder image during the exposure. In addition, the movement of the reflex mirror takes time, limiting the maximum shooting speed. The mirror system can also causes noise and vibration. Partially-reflective (pellicle) fixed mirrors avoid these problems and have been used in a very few designs including the Canon Pellix, but these designs introduce their own problems. These pellicle mirrors reduce the amount of light travelling to the film plane or sensor and also can distort the light passing through them, resulting in a less-sharp image. To avoid the noise and vibration, many professional cameras offer a mirror lock-up feature, however, this feature totally disables the SLR's focusing ability.

Currently, most digital SLRs cannot display a live preview on their rear LCD displays, unlike digicams or bridge cameras, and must be held to the eye to view and compose the image. This situation is changing with the arrival of the Olympus E-330, Olympus E-410, Olympus E-510, Panasonic DMC-L1, Panasonic DMC-L10, Leica Digilux 3, Canon EOS 40D, Canon EOS-1D Mark III, and Nikon D300 cameras.

Electronic viewfinders have the potential to give the 'viewing-experience' of a DSLR (through-the-lens viewing) without many of the disadvantages, but as of 2006 sensor capability and display technology is insufficient for wide acceptance among the advanced amateur or professional markets that purchase and use digital SLRs. The SLR's and DSLR's will probably continue as the foremost system because of the superiority in the use of the viewing and focusing optical system.

Movie Modes

Movie modes are still currently unavailable, and this may continue to be the case as, SLRs and DSLRs will be considered by most photographers as primarily 'still' cameras. This situation may change in the future with more advancements by the camera manufacturers.^[4]

Reliability of SLR's

In some cases of particular SLR models, there tends to be a higher rate of breakdowns than a simpler camera of the same build quality. More expensive SLR's, however, tend to be built to much higher standard than other camera types making their reliability better. Because many SLRs have interchangeable lenses, there is a tendency for dust, sand and dirt to get into the main body of the camera through the mirror box when the lens is removed, thus dirtying or even jamming the mirror movement or the shutter mechanism itself. In addition, these particles can also jam or otherwise hinder the focusing feature of a lens. This problem has been somewhat reduced in DSLRs as some cameras have a built-in sensor cleaning unit.

Price and Affordability

The price of SLRs in general also tends to be somewhat higher than that of other types of cameras, owing to the internal complexity. This is only aggravated by the expense of additional components, such as a flash attachment or various types of lenses. Typically the initial investment in equipment is prohibitive enough to keep some casual photographers away from SLRs.

The Future of SLR's

For the foreseeable future, film-based SLR's may still be produced, as is still the case with the 35mm film-based Nikon F6, and some other 35mm SLR models. This may also be true with some medium-format film-based SLRs. It appears inevitable that the Digital Single Lens Reflex camera design will eclipse film SLR's design in convenience, sales and popularity. These cameras are currently the marketing 'favorite' among advanced amateur and professional photographers. Only those photographers who need a film-based SLR will continue to buy and use such an instrument.

See also

• Asahi Pentax
• Box camera
• Canon (company)
• Digital SLR
• Digital single-lens reflex camera
• Fujifilm
• Kodak
• Lenses for SLR and DSLR cameras
• Nikon
• Optics
• Photographic film
• Rangefinder camera
• Scheimpflug principle
• Twin-lens reflex camera
• Zeiss Ikon
• Zorki

References

External links and sources

• Spira, S. F. The History of Photography as Seen through the Spira Collection. New York: Aperture, 2001. ISBN 0-89381-953-0.
• Photography in Malaysia's Contax History, Part II.
• Digital Lens Multiplier Effect Calculator Calculate the Field of View of a 35mm lens when used on a digital SLR
• SLR Today
• Photo.net website
• Leaf shutter designs
• 'Innovative Cameras' by Massimo Bertacchi