Information about Carbon Dioxide

Carbon dioxide
Other namesCarbonic acid gas; carbonic anhydride; dry ice (solid)
Identifiers
CAS number124-38-9
RTECS numberFF6400000
Properties
Molecular formulaCO2
Molar mass44.0095(14) g/mol
Appearancecolorless gas
Density1,600 kg/m³, solid; 1.98 kg/m³, gas
Melting point −57 °C (216 K) (under pressure)
Boiling point −78 °C (195 K), (sublimes)
Solubility in water1.45 kg/m³
Acidity (pKa)6.35 and 10.33
Viscosity0.07 cP at −78 °C
Dipole momentzero
Related Compounds
Related oxidescarbon monoxide; carbon suboxide; dicarbon monoxide; carbon trioxide
Supplementary data page
Structure and
properties
n, εr, etc.
Thermodynamic
data
Phase behaviour
Solid, liquid, gas
Spectral dataUV, IR, NMR, MS
Except where noted otherwise, data are given for
materials in their standard state
(at 25 C, 100 kPa)

Carbon dioxide is a chemical compound composed of two oxygen atoms covalently bonded to a single carbon atom. It is a gas at standard temperature and pressure and exists in Earth's atmosphere in this state. It is currently at a globally averaged concentration of approximately 375 ppm by volume in the Earth's atmosphere,[1] although this varies both by location and time. Carbon dioxide's chemical formula is CO2.

In general, it is exhaled by animals and utilized by plants during photosynthesis. Additional carbon dioxide is created by the combustion of fossil fuels or vegetable matter, among other chemical processes.

Carbon dioxide is an important greenhouse gas because of its ability to absorb many infrared wavelengths of the Sun's light, and because of the length of time it stays in the Earth's atmosphere. Due to this, and the role it plays in the respiration of plants, it is a major component of the carbon cycle.

In its solid state, carbon dioxide is commonly called dry ice. Carbon dioxide has no liquid state at pressures below 5.1 atm.

Chemical and physical properties

Enlarge picture
Carbon dioxide pressure-temperature phase diagram


For more details on this topic, see Carbon dioxide (data page).
Carbon dioxide is a colorless, odorless gas. When inhaled at concentrations higher than usual atmospheric levels, it can produce a sour taste in the mouth and a stinging sensation in the nose and throat. These effects result from the gas dissolving in the mucous membranes and saliva, forming a weak solution of carbonic acid. This sensation can also occur during an attempt to stifle a burp after drinking a carbonated beverage. Amounts above 800 ppm are considered unhealthy, amounts above 5,000 ppm are considered very unhealthy, and those above about 50,000 ppm are considered dangerous to animal life.[2]


At standard temperature and pressure, the density of carbon dioxide is around 1.98 kg/m³, about 1.5 times that of air. The carbon dioxide molecule (O=C=O) contains two double bonds and has a linear shape. It has no electrical dipole, and as it is fully oxidized, it is moderately reactive and is non-flammable, but will support the combustion of metals such as magnesium.

Enlarge picture
Small pellets of dry ice subliming in air.


At −78.51° C, carbon dioxide changes directly from a solid phase to a gaseous phase through sublimation, or from gaseous to solid through deposition. Solid carbon dioxide is normally called "dry ice", a generic trademark. It was first observed in 1825 by the French chemist Charles Thilorier. Dry ice is commonly used as a versatile cooling agent, and it is relatively inexpensive. As it warms, solid carbon dioxide sublimes directly into the gas phase, making its use convenient as it leaves no liquid. It can often be found in groceries and laboratories, and it is also used in the shipping industry. The largest non-cooling use for dry ice is blast cleaning.

Liquid carbon dioxide forms only at pressures above 5.1 atm; the triple point of carbon dioxide is about 518 kPa at −56.6°C (See phase diagram, above). The critical point is 7,821 kPa at 31.1°C.

An alternative form of solid carbon dioxide, an amorphous glass-like form, is possible, although not at atmospheric pressure.[3] This form of glass, called carbonia, was produced by supercooling heated CO2 at extreme pressure (40–48 GPa or about 400,000 atmospheres) in a diamond anvil. This discovery confirmed the theory that carbon dioxide could exist in a glass state similar to other members of its elemental family, like silicon (silica glass) and germanium. Unlike silica and germania glasses, however, carbonia glass is not stable at normal pressures and reverts back to gas when pressure is released.

History of human understanding

Carbon dioxide was one of the first gases to be described as a substance distinct from air. In the seventeenth century, the Flemish chemist Jan Baptist van Helmont observed that when he burned charcoal in a closed vessel, the mass of the resulting ash was much less than that of the original charcoal. His interpretation was that the rest of the charcoal had been transmuted into an invisible substance he termed a "gas" or "wild spirit" (spiritus sylvestre).

The properties of carbon dioxide were studied more thoroughly in the 1750s by the Scottish physician Joseph Black. He found that limestone (calcium carbonate) could be heated or treated with acids to yield a gas he called "fixed air." He observed that the fixed air was denser than air and did not support either flame or animal life. He also found that when bubbled through an aqueous solution of lime (calcium hydroxide), it would precipitate calcium carbonate. He used this phenomenon to illustrate that carbon dioxide is produced by animal respiration and microbial fermentation. In 1772, English chemist Joseph Priestley published a paper entitled Impregnating Water with Fixed Air in which he described a process of dripping sulfuric acid (or oil of vitriol as Priestley knew it) on chalk in order to produce carbon dioxide, and forcing the gas to dissolve by agitating a bowl of water in contact with the gas.[4]

Carbon dioxide was first liquefied (at elevated pressures) in 1823 by Humphry Davy and Michael Faraday.[5] The earliest description of solid carbon dioxide was given by Charles Thilorier, who in 1834 opened a pressurized container of liquid carbon dioxide, only to find that the cooling produced by the rapid evaporation of the liquid yielded a "snow" of solid CO2.[6]

Isolation

Carbon dioxide may be obtained from air distillation. However, this yields only very small quantities of CO2. A large variety of chemical reactions yield carbon dioxide, such as the reaction between most acids and most metal carbonates. For example, the reaction between sulfuric acid and calcium carbonate (limestone or chalk) is depicted below:

H2SO4+ CaCO3→ CaSO4+ H2CO3


The H2CO3 then decomposes to water and CO2. Such reactions are accompanied by foaming or bubbling, or both. In industry such reactions are widespread because they can be used to neutralize waste acid streams.

The production of quicklime (CaO) a chemical that has widespread use, from limestone by heating at about 850 °C also produces CO2:

CaCO3→ CaO + CO2


The combustion of all carbon containing fuels, such as methane (natural gas), petroleum distillates (gasoline, diesel, kerosene, propane), but also of coal and wood, will yield carbon dioxide and, in most cases, water. As an example the chemical reaction between methane and oxygen is given below.

CH4+ 2 O2→ CO2+ 2 H2O


Iron is reduced from its oxides with coke in a blast furnace, producing pig iron and carbon dioxide:

2 Fe2O3+ 3 C → 4 Fe + 3 CO2


Yeast produces carbon dioxide and ethanol, also known as alcohol, in the production of wines, beers and other spirits:

C6H12O6 → 2 CO2+ 2 C2H5OH


All aerobic organisms produce CO2 when they oxidize carbohydrates, fatty acids, and proteins in the mitochondria of cells. CO2 is the prime energy source and the main metabolic pathway in heterotroph organisms such as animals, and also a secondary energy source in phototroph organisms such as plants when not enough light is available for photosynthesis. The large number of reactions involved are exceedingly complex and not described easily. Refer to (cellular respiration, anaerobic respiration and photosynthesis). Photoautotrophs (i.e. plants, cyanobacteria) use another modus operandi: They absorb the CO2 from the air, and, together with water, react it to form carbohydrates:

nCO2+ nH2O → (CH2O)n+ nO2


Carbon dioxide is soluble in water, in which it spontaneously interconverts between CO2 and H2CO3 (carbonic acid). The relative concentrations of CO2, H2CO3, and the deprotonated forms HCO3- (bicarbonate) and CO32-(carbonate) depend on the pH. In neutral or slightly alkaline water (pH > 6.5), the bicarbonate form predominates (>50%) becoming the most prevalent (>95%) at the pH of seawater, while in very alkaline water (pH > 10.4) the predominant (>50%) form is carbonate. The bicarbonate and carbonate forms are very soluble, such that air-equilibrated ocean water (mildly alkaline with typical pH = 8.2 – 8.5) contains about 120 mg of bicarbonate per liter.

Industrial production

Carbon dioxide is manufactured mainly from six processes:[7]
  1. As a byproduct in ammonia and hydrogen plants, where methane is converted to CO2;
  2. From combustion of carbonaceous fuels;
  3. As a byproduct of fermentation;
  4. From thermal decomposition of CaCO3;
  5. As a byproduct of sodium phosphate manufacture;
  6. Directly from natural carbon dioxide gas wells.

Uses

Carbon dioxide is used by the food industry, the oil industry, and the chemical industry.<ref name="kirk" /> It is used in many consumer products that require pressurized gas because it is inexpensive and nonflammable, and because it undergoes a phase transition from gas to liquid at room temperature at an attainable pressure of approximately 60 bar (870 psi, 59 atm), allowing far more carbon dioxide to fit in a given container than otherwise would. Life jackets often contain canisters of pressured carbon dioxide for quick inflation. Aluminum capsules are also sold as supplies of compressed gas for airguns, paintball markers, for inflating bicycle tires, and for making seltzer. Rapid vaporization of liquid CO2 is used for blasting in coal mines.

Carbon dioxide is used to produce carbonated soft drinks and soda water. Traditionally, the carbonation in beer and sparkling wine comes about through natural fermentation, but some manufacturers carbonate these drinks artificially. A candy called Pop Rocks is pressurized with carbon dioxide gas at about 40 bar (600 psi). When placed in the mouth, it dissolves (just like other hard candy) and releases the gas bubbles with an audible pop.

Leavening agents produce carbon dioxide to cause dough to rise. Baker's yeast produces carbon dioxide by fermentation within the dough, while chemical leaveners such as baking powder and baking soda release carbon dioxide when heated or if exposed to acids.



Carbon dioxide is the most commonly used compressed gas for pneumatic systems in combat robots.

Carbon dioxide extinguishes flames, and some fire extinguishers, especially those designed for electrical fires, contain liquid carbon dioxide under pressure. Carbon dioxide also finds use as an atmosphere for welding, although in the welding arc, it reacts to oxidize most metals. Use in the automotive industry is common despite significant evidence that welds made in carbon dioxide are brittler than those made in more inert atmospheres, and that such weld joints deteriorate over time because of the formation of carbonic acid. It is used as a welding gas primarily because it is much less expensive than more inert gases such as argon or helium.

Liquid carbon dioxide is a good solvent for many organic compounds, and is used to remove caffeine from coffee. First, the green coffee beans are soaked in water. The beans are placed in the top of a column seventy feet (21 meters) high. The carbon dioxide fluid at about 93 degrees Celsius enters at the bottom of the column. The caffeine diffuses out of the beans and into the carbon dioxide.

Carbon dioxide has begun to attract attention in the pharmaceutical and other chemical processing industries as a less toxic alternative to more traditional solvents such as organochlorides. It's used by some dry cleaners for this reason. (See green chemistry.)

Plants require carbon dioxide to conduct photosynthesis, and greenhouses may enrich their atmospheres with additional CO2 to boost plant growth. It has been proposed that carbon dioxide from power generation be bubbled into ponds to grow algae that could then be converted into biodiesel fuel.[8] High levels of carbon dioxide in the atmosphere effectively exterminate many pests. Greenhouses will raise the level of CO2 to 10,000 ppm (1%) for several hours to eliminate pests such as whiteflies, spider mites, and others.

In medicine, up to 5% carbon dioxide is added to pure oxygen for stimulation of breathing after apnea and to stabilize the O2/CO2 balance in blood.

A common type of industrial gas laser is the carbon dioxide laser.

Carbon dioxide can also be combined with limonene oxide from orange peels or other epoxides to create polymers and plastics.[9]

Carbon dioxide is used in enhanced oil recovery where it injected into or adjacent to producing oil wells, usually under supercritical conditions. It acts as both a pressurizing agent and, when dissolved into the underground crude oil, significantly reduces its viscosity, enabling the oil to flow more rapidly through the earth to the removal well.[10] In mature oil fields, extensive pipe networks are used to carry the carbon dioxide to the injection points.

In the chemical industry, carbon dioxide is used for the production of urea, carbonates and bicarbonates, and sodium salicylate.

Liquid and solid carbon dioxide are important refrigerants, especially in the food industry, where they are employed during the transportation and storage of ice cream and other frozen foods. Solid carbon dioxide is called "dry ice" and is used for small shipments where refrigeration equipment is not practical.

Liquid carbon dioxide (industry nomenclature R744 / R-744) was used as a refrigerant prior to the discovery of R-12 and is likely to enjoy a renaissance due to environmental concerns. Its physical properties are highly favorable for cooling, refrigeration, and heating purposes, having a high volumetric cooling capacity. Due to its operation at pressures of up to 130 bars, CO2 systems require highly resistant components that have been already developed to serial production in many sectors. In car air conditioning, in more than 90% of all driving conditions, R744 operates more efficiently than systems using R-134a. Its environmental advantages (GWP of 1, non-ozone depleting, non-toxic, non-flammable) could make it the future working fluid to replace current HFCs in cars, supermarkets, hot water heat pumps, among others. Some applications: Coca-Cola has fielded CO2-based beverage coolers and the US Army is interested in CO2 refrigeration and heating technology.[11][12]

By the end of 2007, the global car industry is expected to decide on the next-generation refrigerant in car air conditioning. CO2 is one discussed option.(see The Cool War)

In the Earth's atmosphere

Enlarge picture
Atmospheric CO2 concentrations measured at Mauna Loa Observatory.


Further information: Carbon dioxide in the Earth's atmosphere


Carbon dioxide in earth's atmosphere is considered a trace gas, and is measured in parts per million. Current concentration levels average approximately 385 ppmv, which represents a total of around 800 gigatons of carbon. Its concentration can vary considerably on a regional basis: in urban areas it is generally higher, and indoors can reach 10 times the atmospheric concentration.

Carbon dioxide is a greenhouse gas; see greenhouse effect for more.

It is observed that due to human activities such as the combustion of fossil fuels and deforestation, the concentration of atmospheric carbon dioxide has increased by about 35% since the beginning of the age of industrialization.[13]

Five hundred million years ago carbon dioxide was 20 times more prevalent than today, decreasing to 4-5 times during the Jurassic Period and then maintained a slow decline until the industrial revolution.[14].

Up to 40% of the gas emitted by a volcano during a subaerial volcanic eruption is carbon dioxide.[15] However, human activities currently release more than 130 times the amount of CO2 emitted by volcanoes. According to the best estimates, volcanoes release about 130-230 million tonnes (145-255 million tons) of CO2 into the atmosphere each year. Emissions of CO2 by human activities amount to about 27 billion tonnes per year (30 billion tons).[16]

In the oceans

There is about 50 times as much carbon dissolved in the oceans in the form of CO2 and CO2 hydration products as exists in the atmosphere http://www.whoi.edu/oceanus/viewArticle.do?id=17726.

Biological role

Carbon dioxide is an end product in organisms that obtain energy from breaking down sugars, fats and amino acids with oxygen as part of their metabolism, in a process known as cellular respiration. This includes all plants, animals, many fungi and some bacteria. In higher animals, the carbon dioxide travels in the blood from the body's tissues to the lungs where it is exhaled. In plants using photosynthesis, carbon dioxide is absorbed from the atmosphere.

Role in photosynthesis

Plants remove carbon dioxide from the atmosphere by photosynthesis, also called carbon assimilation, which uses light energy to produce organic plant materials by combining carbon dioxide and water. Free oxygen is released as gas from the decomposition of water molecules, while the hydrogen is split into its protons and electrons and used to generate chemical energy via photophosphorylation. This energy is required for the fixation of carbon dioxide in the Calvin cycle to form sugars. These sugars can then be used for growth within the plant through respiration. Carbon dioxide gas must be introduced into greenhouses to maintain plant growth, as even in vented greenhouses the concentration of carbon dioxide can fall during daylight hours to as low as 200 ppm, at which level photosynthesis is significantly reduced. Venting can help offset the drop in carbon dioxide, but will never raise it back to ambient levels of 340 ppm. Carbon dioxide supplementation is the only known method to overcome this deficiency. Direct introduction of pure carbon dioxide is ideal, but rarely done because of cost constraints. Most greenhouses burn methane or propane to supply the additional CO2, but care must be taken to have a clean burning system as increased levels of nitrogen oxides (NOx) result in reduced plant growth. Sensors for sulfur dioxide (SO2) and NOx are expensive and difficult to maintain; accordingly most systems come with a carbon monoxide (CO) sensor under the assumption that high levels of carbon monoxide mean that significant amounts of NOx are being produced. Plants can potentially grow up to 50 percent faster in concentrations of 1,000 ppm CO2 when compared with ambient conditions.[17]

Plants also emit CO2 during respiration, so it is only during growth stages that plants are net absorbers. For example a growing forest will absorb many tonnes of CO2 each year, however a mature forest will produce as much CO2 from respiration and decomposition of dead specimens (e.g. fallen branches) as used in biosynthesis in growing plants.[18] Regardless of this, mature forests are still valuable carbon sinks, helping maintain balance in the Earth's atmosphere. Additionally, and crucially to life on earth, phytoplankton photosynthesis absorbs dissolved CO2 in the upper ocean and thereby promotes the absorption of CO2 from the atmosphere.[19]

Animal toxicity

Carbon dioxide content in fresh air varies between 0.03% (300 ppm) and 0.06% (600 ppm), depending on the location (see graphical map of CO2 in real-time).

A person's exhaled breath is approximately 4.5% carbon dioxide.

Internal combustion engines, as used in automobiles, when fuel and ignition are correctly set for best and smoothest power, exhaust CO2% rates of 9.9% to 10.1% by volume are produced. When California Air Resources Board (aka CARB) regulations regarding CO% and HC% are imposed, the CO2% rises to 12% to 15% by volume.

It is dangerous when inhaled in high concentrations (greater than 5% by volume, or 50,000 ppm). The current threshold limit value (TLV) or maximum level that is considered safe for healthy adults for an eight-hour work day is 0.5% (5,000 ppm). The maximum safe level for infants, children, the elderly and individuals with cardio-pulmonary health issues is significantly less.

These figures are valid for pure carbon dioxide. In indoor spaces occupied by people the carbon dioxide concentration will reach higher levels than in pure outdoor air. Concentrations higher than 1,000 ppm will cause discomfort in more than 20% of occupants, and the discomfort will increase with increasing CO2 concentration. The discomfort will be caused by various gases coming from human respiration and perspiration, and not by CO2 itself. At 2,000 ppm the majority of occupants will feel a significant degree of discomfort, and many will develop nausea and headaches. The CO2 concentration between 300 and 2,500 ppm is used as an indicator of indoor air quality.

Acute carbon dioxide toxicity is sometimes known as by the names given to it by miners: blackdamp (also called choke damp or stythe). Miners would try to alert themselves to dangerous levels of carbon dioxide in a mine shaft by bringing a caged canary with them as they worked. The canary would inevitably die before CO2 reached levels toxic to people.

Carbon dioxide caused a great loss of life at Lake Nyos in Cameroon in 1986, when an upwelling of CO2-laden lake water quickly blanketed a large surrounding populated area. The heavier carbon dioxide forced out the life-sustaining oxygen near the surface, killing nearly two thousand people.

Carbon dioxide ppm levels (CDPL) are a surrogate for measuring indoor pollutants that may cause occupants to grow drowsy, get headaches, or function at lower activity levels. To eliminate most Indoor Air Quality complaints, total indoor CDPL must be reduced to below 600. NIOSH considers that indoor air concentrations that exceed 1,000 are a marker suggesting inadequate ventilation. ASHRAE recommends they not exceed 1,000 inside a space. OSHA limits concentrations in the workplace to 5,000 for prolonged periods. The U.S. National Institute for Occupational Safety and Health limits brief exposures (up to ten minutes) to 30,000 and considers CDPL exceeding 40,000 as "immediately dangerous to life and health." People who breathe 50,000 for more than half an hour show signs of acute hypercapnia, while breathing 70,000 – 100,000 can produce unconsciousness in only a few minutes. Accordingly, carbon dioxide, either as a gas or as dry ice, should be handled only in well-ventilated areas.

Human physiology

See also: Arterial blood gas


CO2 is carried in blood in three different ways. (The exact percentages vary depending whether it is arterial or venous blood). The CO2 bound to hemoglobin does not bind to the same site as oxygen. Instead, it combines with the N-terminal groups on the four globin chains. However, because of allosteric effects on the hemoglobin molecule, the binding of CO2 decreases the amount of oxygen that is bound for a given partial pressure of oxygen.

Hemoglobin, the main oxygen-carrying molecule in red blood cells, can carry both oxygen and carbon dioxide, although in quite different ways. The decreased binding to carbon dioxide in the blood due to increased oxygen levels is known as the Haldane Effect, and is important in the transport of carbon dioxide from the tissues to the lungs. Conversely, a rise in the partial pressure of CO2 or a lower pH will cause offloading of oxygen from hemoglobin. This is known as the Bohr Effect.

Carbon dioxide may be one of the mediators of local autoregulation of blood supply. If its levels are high, the capillaries expand to allow a greater blood flow to that tissue.

Bicarbonate ions are crucial for regulating blood pH. A person's breathing rate influences the level of CO2 in their blood. Breathing that is too slow or shallow can cause respiratory acidosis, while breathing that is too rapid may lead to hyperventilation, which may cause respiratory alkalosis.

Although the body requires oxygen for metabolism, low oxygen levels do not stimulate breathing. Rather, breathing is stimulated by higher carbon dioxide levels. As a result, breathing low-pressure air or a gas mixture with no oxygen at all (such as pure nitrogen) may lead to loss of consciousness. This is especially perilous for high-altitude fighter pilots. It is also why flight attendants instruct passengers, in case of loss of cabin pressure, to apply the oxygen mask to themselves first before helping others — otherwise one risks going unconscious without being aware of the imminent peril.<ref name='solarnav' />

According to a study by the United States Department of Agriculture, an average person's respiration generates approximately 450 liters (roughly 900 grams) of carbon dioxide per day.[21]

See also

References

1. ^ Whorf, T.P., Keeling, CD (2005). "Atmospheric CO2 records from sites in the SIO air sampling network.".  Period of record: 1958-2004
2. ^ Staff (16 August 2006). Carbon dioxide: IDLH Documentation. National Institute for Occupational Safety and Health. Retrieved on 2007-07-05.
3. ^ Santoro, M.; et al (2006). "Amorphous silica-like carbon dioxide". Nature 441 (7095): 857-860. DOI:10.1038/nature04879. ISSN 0028-0836. 
4. ^ Priestley, Joseph (1772). "Observations on Different Kinds of Air". Philosophical Transactions 62: 147-264. ISSN 0260-7085. 
5. ^ Davy, Humphry (1823). "On the Application of Liquids Formed by the Condensation of Gases as Mechanical Agents". Philosophical Transactions 113: 199-205. ISSN 0261-0523. 
6. ^ Duane, H.D. Roller; M. Thilorier (1952). "Thilorier and the First Solidification of a "Permanent" Gas (1835)". Isis 43 (2): 109–113. ISSN 0021-1753. 
7. ^ Pierantozzi, Ronald (2001). "Carbon Dioxide". Kirk-Othmer Encyclopedia of Chemical Technology. Wiley. DOI:10.1002/0471238961.0301180216090518.a01.pub2. 
8. ^ Clayton, Mark. "Algae - like a breath mint for smokestacks", Christian Science Monitor, 2006-01-11. Retrieved on 2007-10-11. 
9. ^ Davidson, Sarah (Jan. 17, 2005). Sweet and environmentally beneficial discovery: Plastics made from orange peel and a greenhouse gas. Cornell News. Retrieved on 2007-09-09.
10. ^ Austell, J Michael (2005). "CO2 for Enhanced Oil Recovery Needs - Enhanced Fiscal Incentives". Exploration & Production: The Oil & Gas Review -. Retrieved on 2007-09-28. 
11. ^ THE COCA-COLA COMPANY ANNOUNCES ADOPTION OF HFC-FREE INSULATION IN REFRIGERATION UNITS TO COMBAT GLOBAL WARMING. The Coca-Cola Company (2006-06-05). Retrieved on 2007-10-11.
12. ^ "Modine reinforces its CO2 research efforts", R744.com, 2007-06-28. 
13. ^ [1]
14. ^ Climate and CO2 in the Atmosphere. Retrieved on 2007-10-10.
15. ^ Sigurdsson, H. et al., (2000) Encyclopedia of Volcanoes, San Diego, Academic Press
16. ^ Volcanic Gases and Their Effects. Retrieved on 2007-09-07.
17. ^ Blom, T.J.; W.A. Straver; F.J. Ingratta; Shalin Khosla; Wayne Brown (2002-12). Carbon Dioxide In Greenhouses. Retrieved on 2007-06-12.
18. ^ Global Environment Division Greenhouse Gas Assessment Handbook - A Practical Guidance Document for the Assessment of Project-level Greenhouse Gas Emissions. World Bank. Retrieved on 2007-11-10.
19. ^ Falkowski, P.; Scholes, R.J.; Boyle, E.; Canadell, J.; Canfield, D.; Elser, J.; Gruber, N.; Hibbard, K.; Hogberg, P.; Linder, S.; Mackenzie, F.T.; Moore, B 3rd.; Pedersen, T.; Rosenthal, Y.; Seitzinger, S.; Smetacek V.; Steffen W. (2000). "The global carbon cycle: a test of our knowledge of earth as a system". Science 290 (5490): 291-296. DOI:10.1126/science.290.5490.291. ISSN 0036-8075. 
20. ^ CARBON DIOXIDE. solarnavigator.net. Retrieved on 2007-10-12.
21. ^ Hannan, Jerry. Your Role in the "Greenhouse Effect". Retrieved on 2006-04-19.

External links

43 (2): 109-113.
..... Click the link for more information.
CAS registry numbers are unique numerical identifiers for chemical compounds, polymers, biological sequences, mixtures and alloys. They are also referred to as CAS numbers, CAS RNs or CAS #s.
..... Click the link for more information.
A chemical formula is a concise way of expressing information about the atoms that constitute a particular chemical compound. A chemical formula is also a short way of showing how a chemical reaction occurs.
..... Click the link for more information.
Molar mass, symbol M,[1] is the mass of one mole of a substance (chemical element or chemical compound).[2] It is a physical property which is characteristic of each pure substance.
..... Click the link for more information.
In physics, density is mass m per unit volume V—how heavy something is compared to its size. A small, heavy object, such as a rock or a lump of lead, is denser than a lighter object of the same size or a larger object of the same weight, such as pieces of
..... Click the link for more information.
The melting point of a crystalline solid is the temperature range at which it changes state from solid to liquid. Although the phrase would suggest a specific temperature and is commonly and incorrectly used as such in most textbooks and literature, most crystalline compounds
..... Click the link for more information.
boiling point of a liquid is the temperature at which the vapor pressure of the liquid equals the environmental pressure surrounding the liquid.[1][2][3][4]
..... Click the link for more information.
Sublimation of an element or compound is a transition from the solid to gas phase with no intermediate liquid stage. Sublimation is a phase transition that occurs at temperatures and pressures below the triple point (see phase diagram).
..... Click the link for more information.
Solubility is a physical property referring to the ability for a given substance, the solute, to dissolve in a solvent.[1] It is measured in terms of the maximum amount of solute dissolved in a solvent at equilibrium. The resulting solution is called a saturated solution.
..... Click the link for more information.
Water is a common chemical substance that is essential to all known forms of life.[1] In typical usage, water refers only to its liquid form or state, but the substance also has a solid state, ice, and a gaseous state, water vapor.
..... Click the link for more information.
An acid dissociation constant, denoted by Ka, is an equilibrium constant for the dissociation of a weak acid. According to the Brønsted-Lowry theory of acids and bases an acid is only recognised by its reaction with a base.
..... Click the link for more information.
Viscosity is a measure of the resistance of a fluid to deform under either shear stress or extensional stress. It is commonly perceived as "thickness", or resistance to flow.
..... Click the link for more information.
The poise (symbol P; IPA: /pwɑːz/) is the unit of dynamic viscosity in the centimetre gram second system of units. It is named after Jean Louis Marie Poiseuille.
..... Click the link for more information.
An oxide is a chemical compound containing at least one oxygen atom and other elements. Most of the earth's crust consists of oxides. Oxides result when elements are oxidized by air.
..... Click the link for more information.
Carbon monoxide, with the chemical formula CO, is a colorless, odorless, and tasteless gas. It is the product of the incomplete combustion of carbon-containing compounds, notably in internal-combustion engines.
..... Click the link for more information.
Carbon suboxide, or tricarbon dioxide, C3O2, is a colorless pungent gas, with four cumulative double bonds, making it a cumulene. It is closely related to CO, CO2 and C2O, and other oxides of carbon.
..... Click the link for more information.
Dicarbon monoxide (C2O) is an extremely reactive molecule that contains two carbon atoms and one oxygen atom. It is covalently bonded. It is an intermediate in the photolysis of carbon suboxide.
..... Click the link for more information.
Carbon trioxide (CO3) is an unstable product of reactions between carbon dioxide (CO2) and atomic oxygen (O). [1] It is different from the carbonate ion (CO32-).
..... Click the link for more information.
Aqueous Solubility of CO2 at 101.3 kPa (1 atm) partial pressure[6]

Temperature Dissolved
CO2 volume
per volume H2O
grams CO2 per
100 ml H2O

0 °C 1.713 0.
..... Click the link for more information.
The refractive index (or index of refraction) of a medium is a measure for how much the speed of light (or other waves such as sound waves) is reduced inside the medium. For example, typical glass has a refractive index of 1.
..... Click the link for more information.
The relative static permittivity (or static relative permittivity) of a material under given conditions is a measure of the extent to which it concentrates electrostatic lines of flux.
..... Click the link for more information.
Ultraviolet-visible spectroscopy or ultraviolet-visible spectrophotometry (UV/ VIS) involves the spectroscopy of photons and spectrophotometry. It uses light in the visible and adjacent near ultraviolet (UV) and near infrared (NIR) ranges.
..... Click the link for more information.
Infrared spectroscopy (IR spectroscopy) is the subset of spectroscopy that deals with the infrared region of the electromagnetic spectrum. It covers a range of techniques, the most common being a form of absorption spectroscopy.
..... Click the link for more information.
Nuclear magnetic resonance spectroscopy most commonly known as NMR spectroscopy is the name given to the technique which exploits the magnetic properties of certain nuclei. This phenomenon and its origins are detailed in a separate section on Nuclear magnetic resonance.
..... Click the link for more information.
Mass spectrometry (previously called mass spectroscopy ()[1] or informally, "mass-spec" and MS) is an analytical technique used to measure the mass-to-charge ratio of ions.
..... Click the link for more information.
standard state of a material is its state at 1 bar (100 kilopascals exactly). This pressure was changed from 1 atm (101.325 kilopascals) by IUPAC in 1990.[1] The standard state of a material can be defined at any given temperature, most commonly 25 degrees Celsius,
..... Click the link for more information.
Editing of this page by unregistered or newly registered users is currently disabled.
If you are prevented from editing this page, and you wish to make a change, please discuss changes on the talk page, request unprotection, log in, or .
..... Click the link for more information.
2, −1
(neutral oxide)
Electronegativity 3.44 (Pauling scale)
Ionization energies
(more) 1st: 1313.9 kJmol−1
2nd: 3388.3 kJmol−1
3rd: 5300.5 kJmol−1

Atomic radius 60 pm
Atomic radius (calc.
..... Click the link for more information.
atom (Greek ἄτομος or átomos meaning "indivisible") is the smallest particle still characterizing a chemical element.
..... Click the link for more information.
Covalent bonding is a form of chemical bonding that is characterized by the sharing of pairs of electrons between atoms, or between atoms and other covalent bonds.
..... Click the link for more information.


This article is copied from an article on Wikipedia.org - the free encyclopedia created and edited by online user community. The text was not checked or edited by anyone on our staff. Although the vast majority of the wikipedia encyclopedia articles provide accurate and timely information please do not assume the accuracy of any particular article. This article is distributed under the terms of GNU Free Documentation License.
Herod_Archelaus


page counter