iPedia Free Information Center

Information about Fm

For the musical use of "modulation" as a change of key, see modulation (music).
Topics in Modulation techniques
Analog modulation
AM | SSB | FM | PM | QAM
Digital modulation
OOK | ASK | PSK | FSK | MSK | QAM | CPM | TCM | OFDM
Spread spectrum
FHSS | DSSS
In telecommunications, modulation is the process of varying a periodic waveform, i.e. a tone, in order to use that signal to convey a message, in a similar fashion as a musician may modulate the tone from a musical instrument by varying its volume, timing and pitch. Normally a high-frequency sinusoid waveform is used as carrier signal. The three key parameters of a sine wave are its amplitude ("volume"), its phase ("timing") and its frequency ("pitch"), all of which can be modified in accordance with a low frequency information signal to obtain the modulated signal.

A device that performs modulation is known as a modulator and a device that performs the inverse operation of modulation is known as a demodulator (sometimes detector or demod). A device that can do both operations is a modem (a contraction of the two terms).

A simple example: A telephone line is designed for transferring audible sounds, for example tones, and not digital bits (zeros and ones). Computers may however communicate over a telephone line by means of modems, which are representing the digital bits by tones, called symbols. You could say that modems play music for each other. If there are four alternative symbols (corresponding to a musical instrument that can generate four different tones, one at a time), the first symbol may represent the bit sequence 00, the second 01, the third 10 and the fourth 11. If the modem plays a melody consisting of 1000 tones per second, the symbol rate is 1000 symbols/second, or baud. Since each tone represents a message consisting of two digital bits in this example, the bit rate is twice the symbol rate, i.e. 2000 bit per second.


The aim of digital modulation is to transfer a digital bit stream over an analog bandpass channel, for example over the public switched telephone network (where a filter limits the frequency range to between 300 and 3400 Hz) or a limited radio frequency band.

The aim of analog modulation is to transfer an analog lowpass signal, for example an audio signal or TV signal, over an analog bandpass channel, for example a limited radio frequency band or a cable TV network channel.

Analog and digital modulation facilitate frequency division multiplex (FDM), where several low pass information signals are transferred simultaneously over the same shared physical medium, using separate bandpass channels.

The aim of digital baseband modulation methods, also known as line coding, is to transfer a digital bit stream over a lowpass channel, typically a non-filtered copper wire such as a serial bus or a wired local area network.

The aim of pulse modulation methods is to transfer a narrowband analog signal, for example a phone call over a wideband lowpass channel or, in some of the schemes, as a bit stream over another digital transmission system.

Analog modulation methods

In analog modulation, the modulation is applied continuously in response to the analog information signal.
Enlarge picture
An audio signal (top) may be carried by an AM or FM radio wave.
Common analog modulation techniques are:

Digital modulation methods

In digital modulation, an analog carrier signal is modulated by a digital bit stream of either equal length signals or varying length signals. This can be described as a form of analog-to-digital conversion. The changes in the carrier signal are chosen from a finite number of alternative symbols (the modulation alphabet).

These are the most fundamental digital modulation techniques:
  • In the case of CW, groupings of on-off keying of varying length signals are used.
  • In the case of PSK, a finite number of phases are used.
  • In the case of FSK, a finite number of frequencies are used.
  • In the case of ASK, a finite number of amplitudes are used.
  • In the case of QAM, an inphase signal (the I signal, for example a cosine waveform) and a quadrature phase signal (the Q signal, for example a sine wave) are amplitude modulated with a finite number of amplitudes. It can be seen as a two channel system. The resulting signal is a combination of PSK and ASK, with a finite number of at least two phases, and a finite number of at least two amplitudes.
Each of these phases, frequencies or amplitudes are assigned a unique pattern of binary bits. Usually, each phase, frequency or amplitude encodes an equal number of bits. This number of bits comprises the symbol that is represented by the particular phase.

If the alphabet consists of alternative symbols, each symbol represents a message consisting of bits. If the symbol rate (also known as the baud rate) is symbols/second (or baud), the data rate is bit/second.

For example, with an alphabet consisting of 16 alternative symbols, each symbol represents 4 bit. Thus, the data rate is four times the baud rate.

In the case of PSK, ASK and QAM, the modulation alphabet is often conveniently represented on a constellation diagram, showing the amplitude of the I signal at the x-axis, and the amplitude of the Q signal at the y-axis, for each symbol.

PSK and ASK, and sometimes also FSK, can be generated and detected using the principle of QAM. The I and Q signals can be combined into a complex valued signal called the equivalent lowpass signal or equivalent baseband signal. This is a representation of the valued modulated physical signal (the so called passband signal or RF signal).

These are the general steps used by the modulator to transmit data:
  1. Group the incoming data into codewords;
  2. Map the codewords to attributes, for example amplitudes of the I and Q signals (the equivalent low pass signal), or frequency or phase values.
  3. Adapt pulse shaping or some other filtering to limit the bandwidth and form the spectrum, typically using digital signal processing
  4. Digital-to-analog conversion (DAC) of the I and Q signals (since today all of the above is normally achieved using digital signal processing, DSP). Sometimes the next step is also achieved using DSP, and then the DAC should be done after that.
  5. Modulate the high-frequency carrier waveform, resulting in that the equivalent low pas signal is frequency shifted into a modulated passband signal or RF signal
  6. Amplification and analog bandpass filtering to avoid harmonic distortion and periodic spectrum


At the receiver, the demodulator typically performs:
  1. Bandpass filtering
  2. Automatic gain control, AGC (to compensate for attenuation)
  3. Frequency shifting of the RF signal baseband I and Q signals, or to an intermediate frequency (IF) signal, or
  4. Sampling and analog-to-digital conversion (ADC) (Sometimes before the above point)
  5. Equalization filtering
  6. Detection of the amplitudes of the I and Q signals, or the frequency or phase of the IF signal;
  7. Quantization of the amplitudes, frequencies or phases to the nearest allowed values, using mapping.
  8. Map the quantized amplitudes, frequencies or phases to codewords (bit groups);
  9. Parallel-to-serial conversion of the codewords into a bit stream
  10. Pass the resultant bit stream on for further processing such as removal of any error-correcting codes.


As is common to all digital communication systems, the design of both the modulator and demodulator must be done simultaneously. Digital modulation schemes are possible because the transmitter-receiver pair have prior knowledge of how data is encoded and represented in the communications system. In all digital communication systems, both the modulator at the transmitter and the demodulator at the receiver are structured so that they perform inverse operations.

The most common digital modulation techniques are: MSK and GMSK are particular cases of continuous phase modulation (CPM). Indeed, MSK is a particular case of the sub-family of CPM known as continuous-phase frequency-shift keying (CPFSK) which is defined by a rectangular frequency pulse (i.e. a linearly increasing phase pulse) of one symbol-time duration (total response signaling).

OFDM is based on the idea of Frequency Division Multiplex (FDM), but is utilized as a digital modulation scheme. The bit stream is split into several parallel data streams, each transferred over its own sub-carrier using some conventional digital modulation scheme. The sub-carriers are summarized into a OFDM symbol. OFDM is considered as a modulation technique rather than a multiplex technique, since it transfers one bit stream over one communication channel using one sequence of so-called OFDM symbols. OFDM can be extended to multi-user channel access method in the Orthogonal Frequency Division Multiple Access (OFDMA) and MC-OFDM schemes, allowing several users to share the same physical medium by giving different sub-carriers to different users.

Digital baseband modulation or line coding

The term digital baseband modulation is synonymous to line codes, which are methods to transfer a digital bit stream over an analog lowpass channel using a discrete number of signal levels, by modulating a pulse train (a square wave instead of a sinusoidal waveform). Common examples are unipolar, non-return-to-zero (NRZ), Manchester and alternate mark inversion (AMI) coding.

Pulse modulation methods

Pulse modulation schemes aim at transferring a narrowband analog signal over an analog lowpass channel as a two-level quantized signal, by modulating a pulse train. Some pulse modulation schemes also allow the narrowband analog signal to be transferred as a digital signal (i.e. as a quantized discrete-time signal) with a fixed bit rate, which can be transferred over an underlying digital transmission system, for example some line code. They are not modulation schemes in the conventional sense since they are not channel coding schemes, but should be considered as source coding schemes, and in some cases analog-to-digital conversion techniques. Direct-sequence spread spectrum (DSSS) is based on pulse-amplitude modulation.

Miscellaneous modulation techniques

See also

Editing of this page by unregistered or newly registered users is currently disabled due to vandalism.
If you are prevented from editing this page, and you wish to make a change, please discuss changes on the talk page, request unprotection, log in, or .
..... Click the link for more information.
In music, modulation is most commonly the act or process of changing from one key (tonic, or tonal center) to another. This may or may not be accompanied by a change in key signature. Modulations articulate or create the structure or form of many pieces, as well as add interest.
..... Click the link for more information.
frequency modulation (FM) conveys information over a carrier wave by varying its frequency (contrast this with amplitude modulation, in which the amplitude of the carrier is varied while its frequency remains constant).
..... Click the link for more information.
“QAM


Quadrature amplitude modulation (QAM) is a modulation scheme which conveys data by changing (modulating) the amplitude of two carrier waves.
..... Click the link for more information.
On-off keying (OOK) is a type of modulation that represents digital data as the presence or absence of a carrier wave. In its simplest form, the presence of a carrier for a specific duration represents a binary one, while its absence for the same duration represents a
..... Click the link for more information.
Amplitude-shift keying (ASK) is a form of modulation that represents digital data as variations in the amplitude of a carrier wave.

The amplitude of an analog carrier signal varies in accordance with the bit stream (modulating signal), keeping frequency and phase
..... Click the link for more information.
Phase-shift keying (PSK) is a digital modulation scheme that conveys data by changing, or modulating, the phase of a reference signal (the carrier wave).

Any digital modulation scheme uses a number of distinct signals to represent digital data.
..... Click the link for more information.
Frequency-shift keying (FSK) is a modulation scheme in which digital information is transmitted through discrete frequency changes of a carrier wave. The most common form of frequency shift keying is 2-FSK.
..... Click the link for more information.
“QAM


Quadrature amplitude modulation (QAM) is a modulation scheme which conveys data by changing (modulating) the amplitude of two carrier waves.
..... Click the link for more information.
Continuous phase modulation (CPM) is a method for modulation of data commonly used in wireless modems. In contrast to other coherent digital phase modulation techniques where the carrier phase abruptly resets to zero at the start of every symbol (e.g.
..... Click the link for more information.
In telecommunication, trellis modulation (also known as trellis coded modulation, or simply TCM) is a modulation scheme which allows highly efficient transmission of information over band-limited channels such as telephone lines.
..... Click the link for more information.
Orthogonal Frequency-Division Multiplexing (OFDM) — essentially identical to Coded OFDM (COFDM) — is a digital multi-carrier modulation scheme, which uses a large number of closely-spaced orthogonal sub-carriers.
..... Click the link for more information.
Spread-spectrum techniques are methods by which energy generated in a particular bandwidth is deliberately spread in the frequency domain, resulting in a signal with a wider bandwidth.
..... Click the link for more information.
Frequency-hopping spread spectrum (FHSS) is a method of transmitting radio signals by rapidly switching a carrier among many frequency channels, using a pseudorandom sequence known to both transmitter and receiver.
..... Click the link for more information.
In telecommunications, direct-sequence spread spectrum (DSSS) is a modulation technique. As with other spread spectrum technologies, the transmitted signal takes up more bandwidth than the information signal that is being modulated.
..... Click the link for more information.
Telecommunication is the transmission of signals over a distance for the purpose of communication. In modern times, this process typically involves the sending of electromagnetic waves by electronic transmitters, but in earlier times telecommunication may have involved the use of
..... Click the link for more information.
In mathematics, a periodic function is a function that repeats its values after some definite period has been added to its independent variable.

Examples

Everyday examples are seen when the variable is time
..... Click the link for more information.
Waveform means the shape and form of a signal such as a wave moving in a solid, liquid or gaseous medium.

In many cases the medium in which the wave is being propagated does not permit a direct visual image of the form.
..... Click the link for more information.
musician is a person who plays or composes music. Musicians can be classified by their role in creating or performing music:
  • A musician or instrumentalist plays a musical instrument.

..... Click the link for more information.
The volume of a solid object is the three-dimensional concept of how much space it occupies, often quantified numerically. One-dimensional figures (such as lines) and two-dimensional shapes (such as squares) are assigned zero volume in the three-dimensional space.
..... Click the link for more information.
Pitch may refer to:

In music:
  • Pitch (music), the property of a sound or musical tone measured by its perceived frequency
  • Vocal range and instrumental pitch range

..... Click the link for more information.
sine wave or sinusoid is a function that occurs often in mathematics, physics, signal processing, electrical engineering, and many other fields. Its most basic form is:



which describes a wavelike function of time (t) with
..... Click the link for more information.
In telecommunications, a carrier wave, or carrier is a waveform (usually sinusoidal) that is modulated (modified) with an input signal for the purpose of conveying information, for example voice or data, to be transmitted.
..... Click the link for more information.
amplitude is a nonnegative scalar measure of a wave's magnitude of oscillation, that is, the magnitude of the maximum disturbance in the medium during one wave cycle.

Sometimes this distance is called the peak amplitude
..... Click the link for more information.
phase can be readily understood in terms of simple harmonic motion. The same concept applies to wave motion, viewed either at a point in space over an interval of time or across an interval of space at a moment in time.
..... Click the link for more information.
FreQuency is a music video game developed by Harmonix and published by SCEI. It was released in November 2001. A sequel, titled Amplitude was released in 2003.
..... Click the link for more information.
A demodulator is an electronic circuit used to recover the information content from the carrier wave of a signal. The term is usually used in connection with radio receivers, but there are many kinds of demodulators used in many other systems.
..... Click the link for more information.
Modem (from modulate and demodulate) is a device that modulates an analog carrier signal to encode digital information, and also demodulates such a carrier signal to decode the transmitted information.
..... Click the link for more information.
A digital system is one that uses discrete values (often electrical voltages), representing numbers or non-numeric symbols such as letters or icons, for input, processing, transmission, storage, or display, rather than a continuous range of values (ie, as in an analog system).
..... Click the link for more information.
Channel, in communications (sometimes called communications channel), refers to the used to convey information from a sender (or transmitter) to a receiver.

Overview

A Channel can take many forms.
..... Click the link for more information.


This article is copied from an article on Wikipedia.org - the free encyclopedia created and edited by online user community. The text was not checked or edited by anyone on our staff. Although the vast majority of the wikipedia encyclopedia articles provide accurate and timely information please do not assume the accuracy of any particular article. This article is distributed under the terms of GNU Free Documentation License.
Herod_Archelaus


page counter